Male Rod End Connector supplied as standard at both ends of all Conduit Rods. Threaded end allows the connection of other Rod Accessories

M342/4 Swivel Connector.
An Ideal accessory to have when a single rod is not long enough for the duct length to be rodded. Two rods can be screwed together. Suitable for both 9mm, 11mm & 14mm Rod

Connector used to repair breakage’s to Conduit Rod, the fitting is used with ADH1 Adhesive which is included in the kit.

High quality glass fibre reinforced helically wound epoxy rod giving good adhesion properties for the outer polyethylene coating. This construction gives excellent bending elasticity which makes it ideal for short to long installations into ducts. It is an ideal and fast way of installing draw ropes and winch ropes into ducts, ready for cable pulling operations.

Used to guide Conduit Rod around bends, available with Spring End and also Wire Rope End/Flexible Leader which have the added facility of being able to pull back draw rope without reverting to a standard guide tip.

Used to prove there are no restrictions within the duct.
Approximately 240mm long fitted with a threaded rod and pulling eye each end to give an approx. overall length of 350mm.

Supplied as standard with all Conduit Rods.
The Tip guides the Rod through the Duct, the Eye allows pulling rope to be attached to the Rod.

PRG1 Protective Rod Guide supplied with all Conduit Rod Reels, Used to guide the rod while being pulled off the reel. (Image Top Left)

GB1 Guide Ball. Used to assist Conduit Rod around bends, suitable for 9mm, 11mm & 14mm Rod. (Image Top Right)

LDS2 Shackle suitable for 9mm, 11mm & 14mm Rod, Used with Guide Tip when a larger pulling eye is required. (Image Bottom Left)

ADH1 3ml Adhesive Used to glue End Connectors to Conduit Rod. (Image Bottom Right)

For Duct proving. Painted Steel 240mm long fitted with threaded steel rod and pulling eye each end to give overall length 350mm

SEB’s Rope Blowing Tee is a product designed for installing draw ropes into cable ducts. The Rope Blowing Tee is connected to the inlet of a Pipe Stopper supplied separately and then connected to the airline from a pneumatic compressor. The Draw Rope is then fed through the hole in the end of the Rope Blowing Tee and attached to a line blowing dart or Foam Pig.

Foam Pigs are used to remove dust or fluids from all pipe materials. They are generally pushed through a pipe using air or water pressure, although, they can be supplied with a facility to allow them to be pulled through a pipe by a winch.

Cylindrical Brush with Polypropylene Centres drilled and fitted with threaded steel Rod, Steel end caps and pulling eye each end.
Overall length including Eye 350mm.

High quality glass fibre reinforced helically wound epoxy rod giving good adhesion properties for the outer polyethylene coating. This construction gives excellent bending elasticity which makes it ideal for short to long installations into ducts. It is an ideal and fast way of installing draw ropes and winch ropes into ducts, ready for cable pulling operations.

High quality glass fibre reinforced helically wound epoxy rod giving good adhesion properties for the outer polyethylene coating. This construction gives excellent bending elasticity which makes it ideal for short to long installations into ducts. It is an ideal and fast way of installing draw ropes and winch ropes into ducts, ready for cable pulling operations.

High quality glass fibre reinforced helically wound epoxy rod giving good adhesion properties for the outer polyethylene coating. This construction gives excellent bending elasticity which makes it ideal for short to long installations into ducts. It is an ideal and fast way of installing draw ropes and winch ropes into ducts, ready for cable pulling operations.

High-quality glass fiber reinforced helically wound epoxy rod giving good adhesion properties for the outer polyethylene coating. This construction gives excellent bending elasticity which makes it ideal for short to long installations into ducts. It is an ideal and fast way of installing draw ropes and winch ropes into ducts, ready for cable pulling operations.